Description
Product Overview
The A0760GP is a general-purpose piezoelectric (ICP) accelerometer from Emerson’s machinery health line — a stainless-steel, hermetically welded sensor that converts casing vibration into a low-impedance analog voltage at a nominal 100 mV/g. Internally it combines a ceramic shear-mode sensing element with a built-in charge amplifier, so it runs on a simple 2–20 mA constant-current excitation pair (18–28 VDC) over the same two conductors that carry the signal back — no separate preamplifier, no charge cable, no impedance-matching box at the cabinet. That package is what makes it usable on the plant floor: a technician can mount it on a bearing housing with a 1/4-28 stud, plug in a coiled cable, and read a clean spectrum on a portable collector, or leave it installed as the permanent pickup for an online monitoring rack. It covers 0.5 Hz to 10 kHz (±3 dB), which spans both the shaft-speed and bearing-fault bands, and every unit ships with a multi-point calibration certificate so repeated measurements on the same machine are directly comparable.
Technical Specifications
- Brand: Emerson
- Model: A0760GP
- Product Type: General-purpose ICP piezoelectric accelerometer, single-axis, top-exit
- Sensitivity: 100 mV/g (10.2 mV/m/s²), ±5%, multi-point calibrated
- Measurement Range: ±50 g peak (±490 m/s²)
- Frequency Range: 0.5–10,000 Hz at ±3 dB (30–600,000 cpm); 1.2–5,000 Hz at ±5% linearity
- Mounted Resonant Frequency: 25 kHz nominal
- Amplitude Linearity: ±1% (zero-based straight-line method)
- Transverse Sensitivity: ≤7%
- Input (excitation): 18–28 VDC constant-current supply, 2–20 mA
- Output (signal): Voltage output proportional to acceleration; output bias 8–12 VDC; output impedance <200 Ω
- Noise / Resolution: Broadband resolution 350 µg (3434 µm/s²), 1–10 kHz
- Settling / Discharge: Settling time ≤2 s within 1% of bias; discharge time constant ≥0.3 s
- Shock Limit: 5000 g peak (49,050 m/s²)
- Operating Temp: -54 to +121 °C (-65 to +250 °F), sensitivity deviation -20% to +10% across the range
- Sensor Element: Ceramic shear type
- Housing: Stainless steel, welded hermetic seal; case isolation >10⁸ Ω
- Connector: 2-pin MIL-C-5015, top exit
- Mounting: 1/4-28 UNF-2B threaded base; recommended torque 2–5 lb-ft (2.7–6.8 Nm)
- Dimensions / Weight: Approx. Φ18 x 42.2 mm overall; 51 g (1.8 oz)
- Supplied Accessories: 1/4-28 mounting stud, multi-point calibration certificate
- Warranty: One Year
- Condition: 100% New & Original
Key Notes
- The scale factor must be entered in the monitoring software as 100 mV/g; a wrong factor silently corrupts amplitude trending and alarm levels even though the waveform still looks plausible.
- Mounting quality sets the usable bandwidth — a stud mount gets the full 10 kHz range, a magnet mount and a handheld probe progressively roll off the high-frequency bearing-fault band, so do not compare spectra taken with different mounting methods.
- The MIL-C-5015 connector is not waterproof once the cable is removed; cap the connector and keep the mating face clean, and check the hermetic seal is not disturbed by over-torquing the stud.







Reviews
There are no reviews yet.