Description
Product Overview
The PPC-R22.1N-T-Q1-P2-NN-FW is a VisualMotion control unit from the Bosch Rexroth Indramat PPC-R22.1 series — the master that coordinates a group of intelligent digital servo drives and runs the machine logic in the same CPU. It occupies slot 00 of a RECO02 rack, shares the LocalReco 02 backplane with local I/O and PLC modules, and commands drives over a SERCOS fibre-optic ring, so interpolation, cam synchronization and I/O interlocks stay inside one deterministic loop instead of being split between a PLC and separate motion cards. This suffix set is specific: Q1 adds the DAQ03 Link Ring cross-communication interface for master/slave coupling between VisualMotion controls, P2 adds a DPS01 PROFIBUS-DP slave port for process-data exchange with a higher-level controller, and FW indicates the unit ships with firmware (GPP 11 for VisualMotion 11). On a printing, packaging or machine-tool line with an existing RECO02 rack, this unit is the drop-in replacement path: same slot, same SERCOS ring, same project.
Technical Specifications
- Brand: Bosch Rexroth (Indramat)
- Model: PPC-R22.1N-T-Q1-P2-NN-FW
- Series: PPC-R22.1, VisualMotion 11 motion and logic controller
- Housing / Form Factor: RECO02 control unit, design version 1, installs in slot 00 (leftmost) of the RECO02 rack
- Processor / Memory: PowerPC-based controller; 32 MB SDRAM main memory, 128 kB NVRAM program memory, 32 MB CompactFlash programming module
- Drive Communication: SERCOS fibre-optic interface, up to 16 Mbaud; up to 40 intelligent digital drives per controller (drive count depends on firmware release and drive mix)
- Fieldbus: PROFIBUS-DP slave interface (DPS01), up to 64 words of process data
- Cross Communication: DAQ03 Link Ring interface for master/slave coupling between VisualMotion controls
- Ethernet: Onboard 100 Mbaud, full duplex, link ring interface supported
- Serial Ports: 2x RS-232, max. 115.200 baud
- Digital I/O: 3 digital inputs (input delay 50 µs), 2 digital outputs (0.5 A, max. delay 500 µs)
- Status Display: 4-digit alphanumeric display, LEDs for run/fault states
- Input / Output (supply): 24 VDC rated, permissible 19.2–30 VDC (ripple included), tolerance -15% / +20% per EN 61131-2; max. current consumption 1.2 A; permissible ripple 4 Vpp
- Communication (programming): Ethernet and serial service ports for project download, diagnostics and firmware handling
- Operating Temp: 0 to +45 °C
- Protection: IP20
- Expansion: 3 module slots available (slot 1 typically PLS master, slot 2 PROFIBUS-DP slave, slot 3 normally empty)
- Dimensions / Weight: Approx. 217 x 84 x 165 mm (H x W x D); approx. 1.3 kg
- Firmware: GPP 11 (supplied with unit — the “-FW” suffix)
- Warranty: One Year
- Condition: 100% New & Original
Key Notes
- The suffix chain is the configuration: Q1 = DAQ03 cross communication, P2 = DPS01 PROFIBUS-DP slave, NN = no memory expansion, FW = firmware included. A unit with a different suffix will fit the rack but will not match the project’s communication layout.
- This is not hot-swappable — remove rack power before replacement, and back up the project plus NVRAM data first, or the machine logic and drive parameterization are lost with the unit.
- Verify SERCOS ring termination and the PROFIBUS segment terminators after replacement; an unterminated ring on a 16 Mbaud SERCOS link is the most common cause of a “no drive” fault at power-up.








Reviews
There are no reviews yet.